







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Home Additions & ADU: The Huntington Beach Owner’s Guide
Belgard doesn’t make home additions or ADUs. What Belgard makes is the hardscape skin of them: paver patios, walkways, driveways, retaining walls, and the masonry veneer that wraps a new addition or accessory dwelling unit. If you’ve landed here looking for a Belgard part, the honest answer is that the “part” is almost always a hardscape element, and the repair or install of that element is what needs matching to the Belgard profile. In Huntington Beach, tearing out and rebuilding the Belgard-surface and hardscape scope on an addition or ADU typically runs $45,000 – $130,000 depending on square footage, whether it’s a full addition or an attached unit, and how much of the exterior finish is Belgard.
Owners usually find the problem slowly. A paver lifts near the addition’s footing. Grout joints hairline-crack along a new retaining wall cap. A patio slab they thought was tied to the new structure heaves and now water pools against the ADU door. Or a prior installer set Belgard pavers over a base that was never compacted to spec, and three winters later the whole field is rocking underfoot. You don’t notice it the day it’s installed. You notice it the first rainy season after.
Which Belgard Models This Applies To

Belgard’s hardscape line is divided into families, and each one has its own base, joint, and cap detail that a good installer has to honor when the material is going against a new addition:
- Belgard pavers (Catalina, Mega-Arbel, Holland, Dublin, and similar profile lines): each has its own thickness and joint width, which determines the base depth and joint sand spec.
- Belgard retaining walls (Tandem, Belair, Diamond): the wall block sets the geogrid layout and cap overhang that protect the addition’s footing from soil pressure.
- Belgard masonry veneer and stone: used as the exterior skin on the addition’s lower wall or the ADU’s shared-wall corner, and tied back to the framing with the correct lath and weep system.
The right part is matched by profile name, color, and dimensions, not “the paver that looks like ours.” Look on the back edge of an ungrouted paver, the underside of a cap block, or the label on a leftover pallet. If the color name isn’t visible, take a photo of the top face next to a tape measure with a quarter lying flat for scale.
OEM versus equivalent: Belgard pavers are matched by profile and color, and Belgard’s own replacement skus are the only guaranteed color match when the run is from an old batch. Quality equivalents (Techo-Bloc, for instance) are often a smart swap when a whole field is being rebuilt, because you’re resetting the entire base anyway and a new profile gets you a fresh color lot. Mixing a Belgard profile with a competitor’s “close enough” color on a repair is where homeowners end up with a patch that never blends. We install Belgard and Techo-Bloc hardscapes, and we’ll tell you which makes sense for a repair versus a rebuild. Barrett & Sons Construction Huntington Beach is an independent service provider and is not affiliated with Belgard.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Belgard Home Additions & ADU Is Failing
The hardscape around a new addition or ADU fails in recognizable patterns. Each symptom points at a specific cause, and fixing the wrong cause costs you twice.
- Pavers “rocking” underfoot. The base wasn’t compacted in lifts, or the soil under it wasn’t properly drained. In Huntington Beach, sandy near-coastal soil drains fast at the surface and holds water 6 inches down, so a shallow base fails first.
- Joint sand washing out after rain. Either the joint sand was the wrong spec, or the pavers were laid too tight to accept a proper joint. Wide joints with polymer sand hold; tight joints shed it.
- Water pooling against the ADU or addition footing. The paver field was set flat instead of with positive slope away from the structure. This is a waterproofing issue first, an aesthetic issue second.
- Hairline cracks in the grout or cap on a Belgard retaining wall. Wall block was set without the geogrid, or the cap was mortared without proper weep points. Both show up as cracks before the wall leans.
- Veneer pulling away from the addition’s framing. Missing or incorrect lath, or the wrong fastener for the substrate. This one looks cosmetic and isn’t – get it looked at before the next rain.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

For Huntington Beach, home additions and ADUs that include a Belgard hardscape scope run $45,000 – $130,000. Standalone ADU construction runs $90,000 – $220,000 when the addition includes a full living unit, and a garage conversion runs $30,000 – $80,000. The Belgard portion – patios, walkways, retaining walls, veneer – is typically a line item within those ranges, and it varies most with square footage of hardscape, retaining wall height, and whether we’re matching an existing Belgard profile or rebuilding the whole field.
What drives the range:
- Base prep. Excavation, geotextile, compacted aggregate, and slope are most of the cost and most of the durability.
- Retaining walls over 4 feet. These require engineering and a permit in Huntington Beach, and the cost reflects the geogrid, drainage, and inspection.
- Veneer tie-back. Correct lath, weep, and flashing add labor but prevent the callbacks.
Every scope, allowance, and change order is written before work starts. Permits pulled and inspections signed on every eligible job. Finished work carries the written 90-Day Done Right Promise.
DIY or Call Us?
Here’s where we’re honest with you: some of the Belgard hardscape work around an addition is genuinely checkable by a homeowner, and some of it isn’t.
Safe to check yourself: take a walk along the paver field after a rain and watch where water flows. Tap the cap on any Belgard retaining wall with a screwdriver handle and listen for hollow spots. Photograph the underside of a lifted paver’s base if you can see it, and note the depth of aggregate under it. Check the weep points along a veneer wall on the south and west exposures – those dry out fastest and crack first in Huntington Beach’s coastal sun.
Where DIY goes wrong: a shallow DIY paver repair on a field that was already failing at the base just moves the failure three feet to the side. A retaining wall more than 4 feet tall is a structural wall and needs engineering and a permit – don’t touch it. Veneer tie-back requires the right lath and fastener for your substrate, and a wrong fastener backing out is a water intrusion problem you’ll find months later. This is not the place for Pinterest instructions.
If you see any of the failing signs above and you’re not sure whether it’s surface or structural, call (844) 320-2945. Free estimate, no trip charge inside the county.
FAQs

How long does a Belgard hardscape around an addition or ADU last in Huntington Beach?
With proper base compaction and drainage, Belgard pavers and retaining walls last 25 to 30 years on the coast. The failure point is almost never the paver itself – it’s the base and the joint integrity. Huntington Beach’s salt air and occasional heavy winter rain run test both. If the base was right, the Belgard holds. If it wasn’t, you’ll know by year three. Call (844) 320-2945 for an exact quote on a repair or rebuild – estimates are free.
Can the paver field be repaired instead of replaced?
Yes, when the failure is isolated. A single settling paver or a localized bad joint can be pulled, re-based, and reset, and the blend can usually be matched if you know the Belgard profile and color. When the base itself is failing across more than a third of the field, repair is throwing money at a moving problem – a rebuild is the honest answer. Call (844) 320-2945 and we’ll tell you which you’re looking at.
How long does a Belgard paver or wall repair take?
Isolated paver repairs are usually a one-day job once the material and profile are confirmed. A retaining wall repair with cap and geogrid reset is typically two to four days depending on wall length and access. When we’re installing hardscape alongside a new addition or ADU, the hardscape scope is scheduled after the framing and veneer inspections, so plan the sequencing accordingly. Call (844) 320-2945 to schedule your free estimate.
How do you source the Belgard material?
We order Belgard and equivalent hardscape materials through our regular supplier channels, matched by profile name, color, and dimensions from your existing install. We don’t claim to carry Belgard stock, and we won’t guess at a color match – if the profile name isn’t legible on a leftover piece, the supplier can often pull a sample to compare. When it makes more sense on a full rebuild, we source Techo-Bloc or another quality line. We don’t touch KraftMaid, Cambria, or Silestone scopes on this page, but we install those brands in kitchens and baths. Call (844) 320-2945 for the free second opinion on any written estimate.
Written by the team at Barrett & Sons Construction Huntington Beach, serving Huntington Beach and nearby areas.












