







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Blanco Home Additions & ADU: The Huntington Beach Owner’s Guide
We build home additions and ADUs in Huntington Beach with finishes and fixtures matched to Blanco spec, and a typical project lands between $45,000 and $130,000 depending on size and whether it’s an attached addition or a detached unit. Projects like these move on a schedule, not same-day, because permits and inspections set the pace here. If your Blanco fixture, sink, or built-in element is what kicked off the call, the failure usually shows up the same way: a slow drip under a Blanco sink base in a new wet-bar addition, a cracked basin in a butler’s pantry, a seam that’s lifting after a slab leak, or a faucet cartridge that won’t hold pressure in a guest bath. In our experience, most Huntington Beach owners discover it a few months after the addition was finished, not the week it was done.
Which Blanco Models This Applies To
Blanco makes kitchen sinks, faucets, and composite basins under several lines – SILGRANIT composite sinks (DIAMOND, PRECIS, IKON, VINTERA), the QUATRUS and CERANA stainless lines, and faucet series like the LINUS, EMPRESSA, and ARTONA. Matching a replacement or a spec-correct install means reading the actual model number, which is typically stamped on a metal tag under the sink flange or embossed on the underside of composite basins. Take a photo of that tag and measure the cutout opening, not just the outer rim – Blanco’s composite bowls often share outside dimensions across product tiers but have different bowl depths and mounting profiles. On the OEM side, a factory Blanco bowl or faucet drops back into the existing cutout with the correct drain hole size (most Blanco composite sinks run a standard 3.5-inch drain, but the strainer depth varies by series). On the aftermarket side, stainless equivalents can save money, but the mounting clips and template often don’t match Blanco’s cutouts exactly. For additions and ADUs, we install Blanco fixtures alongside KraftMaid cabinetry, Cambria and Silestone counters in the same scope, so the sink, faucet, and counter cuts all get measured together before fabrication.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Blanco Home Additions & ADU Is Failing
- Water pooling under the sink base in a new addition. On Blanco composite sinks in ADU kitchens, a failing strainer gasket or a hairline crack at the drain hole is the usual culprit. The addition’s floor framing stays dry for months, then shows staining along the base cabinet edge.
- Faucet dripping or losing pressure. Blanco LINUS and EMPRESSA cartridges wear out, and Huntington Beach’s water hardness accelerates mineral buildup inside the cartridge body. If you’re turning the handle harder to get flow, the cartridge is failing, not the supply line.
- Visible crack or crazing on a SILGRANIT basin. Thermal shock from pouring boiling water into a cold composite bowl, or a dropped cast-iron pan, can spider-crack the surface. Once cracked, the composite absorbs moisture and the crack spreads.
- Lifting or separating at the counter-to-sink seam. In ADU kitchens with heavy daily use, the silicone seal between the Blanco rim and a Cambria or Silestone counter fails and lets water wick under the edge. This happens more often on undermount installs than drop-in.
- Faucet base wobble or seepage at the deck. The mounting nut or O-ring under the faucet deck loosens with repeated use. Left alone, water seeps onto the counter and down behind the cabinet.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Full home additions in Huntington Beach run $45,000 to $130,000. Detached ADU construction lands $90,000 to $220,000, and garage conversions come in at $30,000 to $80,000. A Blanco fixture replacement inside an existing addition or ADU is a small line item – a sink swap typically adds $400 to $1,200 installed including the strainer and drain reconnection, and a faucet cartridge replacement runs $150 to $350. What drives the range on a full addition: foundation work (slab on grade vs. pier and beam in the older Huntington Beach neighborhoods near the bluffs), MEP rough-in, whether the addition touches the kitchen (where KraftMaid, Cambria, or Silestone come into play), and permit and inspection costs. Every scope, allowance, and price change arrives as a written change order before work happens – no surprise invoices at the end. Every eligible job carries permits pulled and inspections signed. All work is covered by the written 90-Day Done Right Promise.
DIY or Call Us?
You can safely do a few things yourself. Photograph the tag under the Blanco sink or faucet, measure the cutout and the bowl depth, check the drain gasket for obvious tearing, and shut off the supply valves before you call anyone. What we’d steer you away from: pulling a Blanco composite sink or faucet body on your own, especially on an undermount install under a stone counter. Composite basins are heavy, the mounting clips are often seized or brittle, and a slipped basin can crack the counter or break a supply line under pressure. Faucet cartridge swaps look simple and go wrong often enough – cross-threaded bodies and broken retaining clips are common. If the fixture is inside a newer addition or ADU and the failure traces back to installation, we’d want to see it anyway before more water gets into the framing. Call (844) 320-2945 and we’ll schedule a look.
FAQs

How long does a Blanco sink or faucet last? A Blanco SILGRANIT composite sink typically holds up 15 to 20 years under normal use, and Blanco faucet cartridges generally last 8 to 12 years before mineral wear shows. Huntington Beach’s water hardness tends to shorten the faucet side of that range.
Can a cracked Blanco sink be repaired instead of replaced? Composite sink cracks can sometimes be filled with a color-matched epoxy repair kit, but on a basin that sees daily use we usually recommend replacement, because repairs tend to open back up within a year. A stainless Blanco sink with a dent or scratch is cosmetic and doesn’t need to be swapped.
How long does a Blanco sink or faucet swap take? A standard drop-in Blanco sink swap runs 2 to 4 hours with the counter already in place. An undermount swap with a stone counter takes longer – often a full day – because the counter may need to come up or the clips need careful removal. Faucet cartridge replacement is a 1 to 2 hour job.
How do you source a Blanco part for my model? We read the model number off the tag or emboss on your fixture, cross-reference the current Blanco catalog for the correct series, and confirm the cutout and drain dimensions before ordering. If the exact part is discontinued, we quote the closest OEM equivalent or a spec-matched aftermarket alternative in writing before ordering. Barrett & Sons Construction Huntington Beach is an independent service provider, not affiliated with Blanco.
Call (844) 320-2945 for a free estimate on any Blanco fixture or addition project in Huntington Beach. We’ll bring a written scope, confirm the part number, and quote the range before a single tool comes out of the truck.
Written by the team at Barrett & Sons Construction Huntington Beach, serving Huntington Beach and nearby areas.












