







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Home Additions & ADU: The Huntington Beach Owner’s Guide
We build and finish Barrette home additions and ADU packages in Huntington Beach, and the installed cost for a typical project lands between $45,000 and $130,000 for additions and $90,000 to $220,000 for a full ADU. “Barrette” on a build like this means a modular or panelized room-addition package, so what usually fails first isn’t the framing – it’s the connection hardware, the flashing at the panel seams, and the weather seal where the addition meets the existing house. Huntington Beach owners tend to find us the same way: a stain on the ceiling under the roof tie-in after a winter storm, a door in the new room that sticks in August and frees up in November, or screws backing out along a panel joint. Barrette kits have real compatibility demands, and this page is about matching them right.
Key takeaways:
- Barrette’s connector and flashing lines are mostly homeowner-installable, but panel tie-ins and roof penetrations are not a weekend job.
- OEM Barrette parts carry the load rating; generic hardware from a big-box bin often doesn’t share the same gauge or slot pattern.
- Salt air and marine humidity in Huntington Beach shorten the life of galvanized fasteners and cheap sealant more than anything else.
- Every eligible addition we build gets its permits pulled and its inspections signed.
Which Barrette Models This Applies To

Barrette makes several lines that show up in home-addition and ADU work, and getting the right part starts with reading the actual stamp or label on the hardware, not guessing from a photo. The Barrette Outdoor Living connectors and tie brackets (joist hangers, post bases, rafter ties, and structural screws) each carry a gauge and a load rating stamped on the metal or molded into the plastic. Panel and room-addition kits use their own labeled connection sets, and the label is the key – the part number usually sits in the middle of a small black-on-white sticker on the bracket or on the end of the bundle.
How to identify the right part:
- Find the stamp. Structural connectors have a part number and a gauge stamp. Photograph it before you call anyone.
- Measure the lumber it holds. A 2×6 joist hanger and a 2×8 joist hanger look close but will not interchange.
- Check the coating. Barrette’s galvanized and G90-rated hardware are not the same; near the coast you want the heavier coating.
OEM versus aftermarket: for Barrette specifically, most of the connectors have a legitimate aftermarket equivalent if you match the gauge and the slot spacing – Simpson Strong-Tie (the similar-sounding but different company) makes cross-compatible brackets that run within a few dollars. Where we don’t compromise is the panel tie-in hardware and the flashing kit; those are Barrette-specific, and a generic substitute is what causes leaks six months in. We’re an independent contractor, not affiliated with Barrette, so we buy the right part for the job rather than push a brand.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Barrette Home Additions & ADU Is Failing
- Water staining at the roof tie-in or panel seam. Barrette flashing kits rely on a specific overlap direction, and reversed overlap in a Huntington Beach winter is the number-one cause of a drip into the new room.
- Sticking doors or windows in the addition. That’s the framing shifting as the connectors loosen – a bent joist hanger or a backed-out structural screw usually turns up under the subfloor.
- Screws backing out along panel joints. Vibration and thermal cycling loosen them; it’s also a sign the wrong drive bit or over-torqued install left them short of the stud.
- Rust creeping in from the fastener heads. Salt air eats a low-grade galvanized screw fast – you’ll see rust halos on the siding within a season or two if the wrong coating was used.
- Gaps between the addition and the original house. That seam should be flashed and sealed with the Barrette kit, not caulk. A visible gap or a soft spot means the connection detail failed.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed Barrette home addition and ADU work in Huntington Beach runs the ranges below. These are installed prices – materials plus our crew’s labor – not the bare part cost, because a bracket that costs $15 is useless without the labor to open the wall, sister a stud, and reseal it.
| Job | Installed range |
|---|---|
| Home addition (Barrette package + finish) | $45,000 – $130,000 |
| ADU construction | $90,000 – $220,000 |
| Garage conversion to ADU | $30,000 – $80,000 |
| Connector / flashing repair (part of a larger job) | quoted as a line item |
What drives the range: the addition’s footprint, how many panel seams need flashing, whether permits and engineering are already in place, and finish level (drywall, flooring, electrical rough-in). Every scope and allowance arrives in writing before we start, and any price change is a written change order before the work moves. The 90-Day Done Right Promise is written on every contract – if something isn’t right after we finish, one call brings Tom back.
DIY or Call Us?
Some of this is genuinely within a homeowner’s reach: you can inspect and photograph a failing Barrette bracket, check for rust at the fastener heads, and note any sticking doors so you can tell us exactly what’s happening. Where DIY goes wrong is anything structural or weatherproofing. A joist hanger set with the wrong nail and a flashing seam reversed will pass the eye test and then let water in for a season before the ceiling shows it. And panel tie-ins and roof penetrations sit in the load path – done wrong they can shift framing or open leaks you can’t see. That’s a job for our crew, and it’s exactly the kind of thing the permit inspector catches.
If your Barrette addition is showing any of the signs above, call (844) 320-2945 for a free estimate. We’ll come out, get eyes on the actual connector, and tell you honestly whether it’s a spot repair or a bigger fix.
FAQs

How long does a Barrette home addition or ADU last? A properly installed and flashed Barrette system should serve 20 to 30 years in Huntington Beach’s coastal climate, but the connectors and flashing are the weak point – expect to inspect the tie-in points every few years and replace degraded fasteners sooner because of the salt air. Call (844) 320-2945 for a specific read on your project.
Can a failing Barrette connector be repaired instead of replaced? Often yes – a single bent joist hanger or a backed-out structural screw can be swapped without tearing out the wall, which keeps the job in the repair cost range rather than the full-addition range. But if the flashing and panel seam are also compromised, repair isn’t enough and a partial rebuild is the honest answer. Estimates are free, so call and we’ll tell you which one you’re looking at.
How long does the swap take? A connector or flashing repair typically takes half a day to a day, while a full addition or ADU package is a weeks-long build that depends on permits and inspection timing. Call (844) 320-2945 and we’ll give you a written scope with a realistic timeline before any work begins.
How do you source the Barrette part? We match the part number, gauge, and coating off the original hardware and order it, or specify a cross-compatible aftermarket equivalent when that’s the smarter buy. We don’t claim to carry parts on a truck or stock them – the right part gets sourced to your job, and we put the specification in writing so you can verify it.
We also work with KraftMaid, Cambria, and Silestone finishes when an addition or ADU includes a new kitchen or bath. Barrett & Sons Construction Huntington Beach has crew members with up to 28 years of experience, and our technicians carry the Barrett name on every visit.
Call (844) 320-2945 to schedule your free estimate. A live person answers the phone 24 hours a day, and we’ll bring a second opinion to any written estimate you already have – no trip charge inside the county, and a permanent 10% Senior & Veteran discount.
Written by the team at Barrett & Sons Construction Huntington Beach, serving Huntington Beach and nearby areas.












