







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Huntington Beach Owner’s Guide
If you’re pricing a Schluter detail for a home addition or ADU in Huntington Beach, plan on $45,000 – $130,000 installed for an addition, $90,000 – $220,000 for a detached or attached ADU, and $30,000 – $80,000 for a garage conversion. The Schluter piece – most often a KERDI waterproofing membrane, a KERDI-BOARD panel, or a DITRA mat in a new bath or laundry – is a small line item inside that number, and it’s the one that decides whether your new wet area holds. We install Schluter systems as part of that work. We’re an independent service provider and not affiliated with Schluter; we buy their parts through normal supply and install them to spec.
Owners usually discover the problem the same way. A shower floor in a new ADU starts to darken at the drain. Grout in a new bath recedes in a hairline line along the wall. Or a tile edge on the new curb feels hollow when you tap it. That hollow sound means trapped water, and in Huntington Beach’s marine air it shows up faster than it does inland.
Which Schluter Models This Applies To

Schluter’s lineup isn’t one part, it’s a family, and matching the right one matters. The relevant pieces for additions and ADUs are KERDI (sheet membrane, 5 mil and 8 mil thicknesses in common rolls), KERDI-BOARD (rigid foam backer panels, typically 1/2″, 5/8″, and 2″ thick), KERDI-BAND (the 5″ and 7″ seaming strips), DITRA and DITRA-HEAT (uncoupling mats, with the heat version carrying the cable), and the KERDI-DRAIN / KERDI-LINE drain assemblies. The compatibility gotcha: KERDI-BOARD thickness is set by the tile weight and the wall assembly, not by what’s on the shelf. A 1/2″ panel on a shower wall that will carry large-format porcelain over 12″ x 24″ isn’t the same call as a 1/2″ panel under 4″ x 4″ mosaic. Get that wrong and you’ll fight deflection. DITRA-HEAT also has to match the thermostat and the cable spacing, so the mat, the cable, and the controller are a set. A membrane is a membrane, but the drain flange, the band, and the thinset are what the inspector looks at.
On the OEM-versus-aftermarket question for Schluter specifically: the branded membrane and the factory drain are worth buying new. They carry the warranty path and the approvals your Huntington Beach permit inspector expects to see. Small accessories like trowels, seam rollers, and corner pieces are fine to source elsewhere. What we don’t do is claim stock. We don’t carry Schluter parts on a truck. We order what the job calls for, and we show you the spec sheet before we install it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
Here’s what a failing membrane or mat actually looks like, and what’s underneath each symptom:
- Dark staining at the drain or along a shower floor joint. Water is getting behind the tile because the KERDI-DRAIN flange wasn’t bonded to the membrane properly, or the thinset under the band cured too dry.
- Grout cracking in a straight line at the wall-to-floor transition. That’s movement. The DITRA mat is supposed to absorb it, so a clean crack usually means the mat wasn’t the right size for the tile, or it wasn’t installed over the full subfloor.
- Hollow-sounding tile on a new curb or shower wall. Trapped moisture or a void under the membrane. Tap it with a screwdriver handle – if it rings dull, it’s not bonded.
- Efflorescence (white powder) on new grout in an ADU bath. Water is traveling through the assembly and drying at the surface. In Huntington Beach’s salt air, this shows up within a season, not years.
- Musty smell in a new laundry or mudroom. A KERDI-BOARD seam wasn’t banded, so the panel is wicking. This is the one that quietly rots framing in an attached garage conversion.
Two things worth knowing for this market: the coastal humidity in Huntington Beach pushes membrane failures to the surface faster than inland cities do, so a leak that would hide for a year in Riverside shows in six months here. And a garage conversion where the slab is original means the DITRA mat is doing extra work against slab moisture – a detail a lot of out-of-area crews skip.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Schluter membrane and drain work is priced inside the addition, not as a standalone part, because the labor is the job. Here’s how the numbers land in Huntington Beach:
- Home Addition: $45,000 – $130,000 installed, with the wet-area waterproofing running roughly $1,800 – $4,500 of that for a full bath and laundry.
- ADU Construction: $90,000 – $220,000, with Schluter waterproofing typically $3,500 – $7,500 across the wet rooms.
- Garage Conversion: $30,000 – $80,000, with a shower and laundry detail usually $1,500 – $3,500.
What drives the range: number of wet areas, drain type (a linear KERDI-LINE costs more than a center drain), and whether the subfloor needs work before the mat goes down. Every scope and every allowance arrives as a written change order before work happens. Permits are pulled and inspections signed on every eligible job. The finished work carries our written 90-Day Done Right Promise.
DIY or Call Us?
You can safely check a few things. Look for staining at the drain, tap for hollow tile, sniff a new laundry for must, and read the label on any membrane box to confirm what you have. What you shouldn’t do yourself is the waterproofing install – and this is the honest part. Getting a KERDI membrane or a KERDI-DRAIN flange wrong isn’t a cosmetic mistake; it’s a slow leak that rots framing behind the tile, and by the time it shows, you’re tearing out a finished bathroom. The 5″ band, the thinset consistency, the drain bond, and the flood test are all things one bad afternoon can ruin. That’s not scare talk, it’s what we see on tear-outs. If your new addition has a wet area that’s failing, call (844) 320-2945 and we’ll look at it.
FAQs

How long should Schluter waterproofing last in a home addition? A properly installed KERDI assembly should last the life of the tile, 30 years or more in a Huntington Beach bath. The membrane rarely fails on its own; the bond at the drain and the banding at seams are what fail first.
Can the membrane be repaired instead of replaced? Sometimes. A localized seam failure can be re-banded and flood-tested without tearing out the whole shower. A failed drain flange usually means pulling the floor tile, so the answer depends on where the leak is. Call (844) 320-2945 for a look before you assume the worst.
How long does the swap take? A single wet-area re-waterproof takes two to four days including the flood test and tile reset. A full bath inside a new ADU runs two to three weeks. We schedule it in writing, with no surprise on the calendar.
How do you source the Schluter part? We order from Schluter’s normal supply channel, matched to your model and spec, and we show you the sheet before install. We’re an independent provider, not affiliated with Schluter, so the part comes from the manufacturer and the install comes from us. We also work with KraftMaid, Cambria, and Silestone on the finishes side of the same jobs.
If you’re planning a home addition or ADU in Huntington Beach and want the wet areas done right the first time, call (844) 320-2945 for a free estimate. Ask for the second opinion on any written estimate you already have – that one’s free too, and there’s no trip charge inside the county.
Written by the team at Barrett & Sons Construction Huntington Beach, serving Huntington Beach and nearby areas.












